Call us at +86 13377766112

Products: Buffered Fiber Optic Cable

Tight Buffered Fiber Optic Cable

Tight Buffered Fiber Optic Cable

Tight buffered fiber optic cable is produced as that fiber is sheathed by buffer material. The selection of top-quality fiber, the specific production equipment and the accurate design assure the performance of the product. To be more specific, a single-mode or multi-mode fiber with a tightly-coated secondary coating structure is called a tight buffered fiber or a tight-packed fiber, and is a double-over-plastic (PVC/PVDF) directly coated on a bare fiber (UV fiber). /LSZH/Hytrel), the outer diameter of the tight-fitting fiber is usually 0.6mm and 0.9mm. It is the basic component for manufacturing various indoor optical cables. It can also be used alone and twice coated with various materials. The tight-fitting fiber can be directly used as a pigtail for the connection of various optical active or passive components, the connection of instruments and terminal equipment, and the like.

READ MORE
100km CWDM SFP 10G module compatible optical module

100km CWDM SFP 10G module compatible optical module

Description of this 100km CWDM SFP 10G module compatible optical module SFP CWDM Optical module CWDM SFP optical module is a low-cost WDM transmission technology for the access layer of the metropoli

READ MORE
EOC 3050 Optical modem

EOC 3050 Optical modem

EOC-3050 Optical modem, as an Ethernet coaxial terminal product, Ethernet access is performed using a coaxial cable. The EoC terminal device has built-in WiFi wireless function, including three 100M Ethermet ports and one high- quality voice interface, which can support various data access requirements such as pure data, data +voice, data + voice + WIFI.

READ MORE
Stranded Layer Non Armored Ribbon Fiber GYFDTA

Stranded Layer Non Armored Ribbon Fiber GYFDTA

GYFDTA uses FRP as the central strength member ensures good tensile resistance,and improves the bending performance.The middle layer of aramid yarn increases the tensile strength of the cable. It has excellent moisture resistance ability:the loose tube is filled with grease to protect the fiber, APL tape prevent the water ingress, then the cable is completed with PE out sheath. It's suitable for aerial and duct application. Because of the good moisture resistance, it can also be used in cable trench. It has the loose tube structure with ribbon cable, which is surrounded by the APL tape. GYFDTA is a good option for interoffice communication,outdoor access network

READ MORE
Insert Type Splitter

Insert Type Splitter

The Insert Type PLC Splitters is branching devices that is used to distribute optical signals to multiple locations for processing. In optical networks, it is often necessary to split an optical signal into many identical signals, or to combine many signals into a single signal. PLC Splitter (Planar lightwave circuit splitter) is a type of optical power management device that is fabricated using silica optical waveguide technology. They are designed for FTTx Passive Optical Networks, CWDM, DWDM and optical cable TV System. PLC Splitter is responsible to distribute optical signals from Central Office (CO) to multiple premise locations.We provides whole series of 1*N and 2*N splitter products that are tailored for specific applications. All prodcts meet GR-1209-CORE-2001 and GR-1221-CORE-1999 requirements.

READ MORE
100G QSFP Dual LC LWDM 10KM Optical Communication QSFP Module

100G QSFP Dual LC LWDM 10KM Optical Communication QSFP Module

The 100G QSFp Optical Module integrates the receiver and transmitter paths on one module. At the transmitting end, the four channels of serial data are recovered, retimed, and passed to the four laser drivers. The laser driver controls a 4-distributed feedback laser (DFB) with center wavelengths of 1296 nm, 1300 nm, 1305 nm, and 1309 nm. The optical signal is multiplexed to a single mode fiber through an industry standard LC connector. On the receiving side, the four optical data stream channels are optically demultiplexed by an integrated optical demultiplexer. Each data stream is recovered by the PIN photodetector and transimpedance amplifier and retimed. The module features a hot-swappable electrical interface, low power consumption and MDIO management interface. Designed according to the QSFP Multi-Source Agreement (MSA), the product features a form factor, optical/electrical connection and digital diagnostic interface, and is compliant with the IEEE 802.3bm standard.

READ MORE
Discounts LC connector 850 1310 1550nm optic Sfp dwdm  optic transceiver module

Discounts LC connector 850 1310 1550nm optic Sfp dwdm optic transceiver module

The SFP+ DWDM optical module adopts an LC optical port and is compatible with IEEE802.3ae and SFF-8472. It has low power consumption, small size, and high speed. The SFP+DWDM optical module is capable of combining a set of optical wavelengths for transmission using one fiber. SFP+DWDM is a wavelength division multiplexing technology that can couple different wavelengths of light into a single-core fiber for transmission. SFP+DWDM requires less spacing and requires additional wavelength control devices. The advantage of SFP+DWDM is that its protocol and transmission speed are irrelevant. The DWDM-based network can transmit data using IP protocol, ATM, SONET/SDH, and Ethernet protocols, and the processed data traffic is between 100Mb/s and 400Gb/s. In this way, a DWDM-based network can transmit different types of data traffic at different speeds on a single laser channel. Mainly used in data center interconnection, SONET/SDH, metropolitan area network, 4G LET wireless network, transmission network, high-speed point-to-point link, Fibre Channel and other environments.

READ MORE
GPON 1280 Optical modem

GPON 1280 Optical modem

GPON-1280 Optical modem, WIFI dual-band wireless connection speed up to 300 Mbps at 24 GHz, and dual-band wireless speed up to 1200 Mbps, support 2/3 layer network protocol and high-quality voice transmission. GPON optical network terminals have reliability, good service quality assurance, manageability scalability and flexible networking features.The GPON standard is the ITU-TG.984 series of standards. The development of the GPON standard considers the support for traditional TDM services, and continues to adopt the 125ms fixed frame structure to maintain the 8K timing continuation. In order to support multiple protocols such as ATM, GPON defines a new package structure GEM:GPONEncapsulaTIonMethod. The data of ATM and other protocols can be mixed and encapsulated into frames.GPON is positioned in the telecom industry for multi-service, QoS-guaranteed full-service access needs, and strives to find an optimal, full-service, and most efficient solution, and proposes to "completely and thoroughly open all protocols." reconsider".

READ MORE