This kind of cable use bare copper to be the center conduction with the Specification is 24AWG and PE to be the dielectric. The jacket is made of Fireproof material, which is so meanful to the Cat5e communication. This Cat5e SFTP cable is conform to the SIO/IEC, TIA/EIA and EN standards. And the electrical characteristics are exceed the lastest Cat5e standards.
100G AOC active optical cable refers to a communication cable that needs to use external energy to convert electrical signals into optical signals or convert optical signals into electrical signals. The optical transceivers at both ends of the optical cable provide photoelectric conversion and optical transmission functions. And the transmission rate reaches 100Gb/s. 100G AOC Optical module This module has a photoelectric conversion device inside, which can convert electrical signals into optical signals with a transmission distance of up to 100 meters. The product has one to four channels, each with a transmission rate of 25.3125 Gb / s and a rate of 100 Gb / s. Its low power consumption, low bit error rate, easy management, high performance, etc. are widely used in short-distance high-speed connections, such as 100 Gigabit Ethernet, 100 Gigabit switches, 100 Gigabit servers, supercomputers, cloud computing and cloud storage.
Fluke passed and Factory lowest price UTP CAT6 Ethernet cable/Network cable 4Pr 24 AWG BC/CCA/CCS/CCAG 305m/roll wholesale CCOFC factory is a professional manufacturer in producing Cat6 UTP/FTP/SFTP/STP/SFFTP/FFTP network cable, Power cable, Coaxial cable, Telephone cable etc. The cat6 network cable are applied to the wiring between the user communication terminal of the residential integrated wiring system and the distribution frame and the distribution frame between the communication terminal of the work area and the junction between the distribution wiring system, and are suitable for high-speed local area network, which is suitable for 240MHz channel bandwidth communication. The cross-shaped conductor divider design enhances near-end crosstalk and impedance performance, increasing bandwidth and signal-to-noise margin.
Fiber patch cords are fiber-optic cables with connectors on both ends that can be connected directly to a computer or other network device. Fiber patch cords are commonly used to connect light emitting devices, light receiving devices, and fiber optic terminal boxes. Single-mode fiber patch cord cores are particularly small in diameter, typically only 9 μm, and have only one light propagation path. It is for this reason that light can only be transmitted along the axis of the fiber, thereby completely avoiding the waste of dispersion and light energy.
Simplex indoor optical cable is made by evenly applying strands of aramid yarns as the strength member over tight buffer fibers and then is completed with a flame retardant sheath(CPR-Cca).
BIDI-SFP optical module: BiDi (Bidirectional): single fiber bidirectional. It uses WDM (ie, wavelength division multiplexing) technology to transmit and receive different center wavelengths in two directions, thereby realizing a bidirectional transmission of optical signals in one fiber. A general optical module has two ports, a TX transmitting port and an RX receiving port, and the BIDI optical module has only one port, which is filtered by a filter in the optical module, and simultaneously performs transmission of a 1310 nm optical signal and reception of a 1550 nm optical signal, or in contrast. Therefore, BIDI modules must be used in pairs. It is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking the port with the network. SFPs can be used and interchanged on a wide variety of switches and routers, can be intermixed in combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.
"GY" means outdoor optical cable for communication, "F" means non-metallic reinforcing member, "T" means ointment filling structure, "Y" means polyethylene sheath. GYFTY is positioned in a loose tube made of a high modulus plastic. At the center of the core is a fiberglass reinforced plastic (FRP), and the loose tube (and the filling rope) is twisted around the central reinforcing core into a compact and round core with a gap in the core filled with a water-blocking filler. The outer core of the cable is extruded with a polyethylene inner sheath to form a cable.
EOC-4051 Optical modem fully complies with the IEEE P1901 standard and China Telecom EOC equipment technical requirements. It has the characteristics of carrier-class operation, manageability and easy maintenance. It is a bridge-type home-side device and realizes ultra-wideband for home/SOHO users through EOC technology. Access. It has one PON uplink interface connected to the central office equipment through optical fibers. The structure is small, supporting the placement of the desktop, wall hanging or placed in the corridor information box. As an Ethernet coaxial terminal product, Ethernet access is performed using a coaxial cable. The EoC terminal device has a built-in Wifi wireless function and includes four 100M Ethernet ports for works with EOC master in Ethernet over coax network.Ability to provide high quality Internet access, voice, IPTV, VoIP and video surveillance.