The structure of the self-supporting pre-terminated drop cable is based on the Butterfly cable, and a metal suspension unit is added. With the continuous extension of the optical fiber like the user end, in order to meet the different uses and requirements, and expand the use range of the butterfly-introducing cable, on the basis of the Pre-terminated Drop Cable, a derivative product of the butterfly-introducing has emerged, the most typical one being The Self-supporting Pre-terminated Drop Cable is introduced into the optical cable.READ MORE
BIDI-SFP optical module: BiDi (Bidirectional): single fiber bidirectional. It uses WDM (ie, wavelength division multiplexing) technology to transmit and receive different center wavelengths in two directions, thereby realizing a bidirectional transmission of optical signals in one fiber. A general optical module has two ports, a TX transmitting port and an RX receiving port, and the BIDI optical module has only one port, which is filtered by a filter in the optical module, and simultaneously performs transmission of a 1310 nm optical signal and reception of a 1550 nm optical signal, or in contrast. Therefore, BIDI modules must be used in pairs. It is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking the port with the network. SFPs can be used and interchanged on a wide variety of switches and routers, can be intermixed in combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.
Simplex indoor optical cable is made by evenly applying strands of aramid yarns as the strength member over tight buffer fibers and then is completed with a flame retardant sheath(CPR-Cca).
C450-fiber optic cabinet is a high-capacity and high-density fiber distribution frame. It adopts high-quality cold-rolled steel frame/electrolytic plate and electrostatic spraying on the whole surface. It is widely used in small and medium-sized integrated wiring projects, equipment room, intelligent community, telecommunications, school. Such projects enable the connection, distribution and scheduling of fiber-optic lines, and the detachable design makes the products more flexible and simple in application.
ADSS cable, the all-media self-supporting optical cable is a non-metallic optical cable which is composed entirely of dielectric materials and contains the necessary support system and can be directly suspended on the power pole. Fibers, 250μm, are positioned in a loose tube made of a high modulus plastics. The tubes are filled with a water-resistant filling compound.
The 100G QSFp Optical Module integrates the receiver and transmitter paths on one module. At the transmitting end, the four channels of serial data are recovered, retimed, and passed to the four laser drivers. The laser driver controls a 4-distributed feedback laser (DFB) with center wavelengths of 1296 nm, 1300 nm, 1305 nm, and 1309 nm. The optical signal is multiplexed to a single mode fiber through an industry standard LC connector. On the receiving side, the four optical data stream channels are optically demultiplexed by an integrated optical demultiplexer. Each data stream is recovered by the PIN photodetector and transimpedance amplifier and retimed. The module features a hot-swappable electrical interface, low power consumption and MDIO management interface. Designed according to the QSFP Multi-Source Agreement (MSA), the product features a form factor, optical/electrical connection and digital diagnostic interface, and is compliant with the IEEE 802.3bm standard.
GYDTA uses steel as the central strength member ensures good tensile resistance,and improves the bending performance. It has excellent moisture resistance ability:the loose tube is filled with grease to protect the fiber, APL tape prevent the water ingress, then the cable is completed with PE out sheath. It's suitable for aerial and duct application. Because of the good moisture resistance, it can also be used in cable trench. It has the loose tube structure with ribbon cable, which is surrounded by the APL tape. GYDTA is a good option for interoffice communication,outdoor access network.
This kind of cable use bare copper to be the center conduction with the Specification is 24AWG and PE to be the dielectric. The jacket is made of Fireproof material, which is so meanful to the Cat5e communication. This Cat5e SFTP cable is conform to the SIO/IEC, TIA/EIA and EN standards. And the electrical characteristics are exceed the lastest Cat5e standards.