Planar lightwave circuit PLC splitter is a type of optical power management device that is fabricated using silica optical waveguide technology.It features small size,high reliability,wide operating wavelength range and good channel-to-channel uniformity,and is widely used in PON networks to realize optical signal power splitting. Bare PLC splitter is putting PLC splitter chip and input, output optical fiber array in a square metal tube, out with the diameter of 0.9mm or 250um bare fiber ,fiber can be welded, can also be processing various types of optical fiber connector. We provides whole series of 1*N and 2*N splitter products that are tailored for specific applications.All products meet "YD/T1117-2001 All optical fiber branching device technical conditions","YD-T 2000-209 PLC Integrated optical devices PLC optical power splitter"etc, and are certified by TLC for network deployment.
EOC-4051 Optical modem fully complies with the IEEE P1901 standard and China Telecom EOC equipment technical requirements. It has the characteristics of carrier-class operation, manageability and easy maintenance. It is a bridge-type home-side device and realizes ultra-wideband for home/SOHO users through EOC technology. Access. It has one PON uplink interface connected to the central office equipment through optical fibers. The structure is small, supporting the placement of the desktop, wall hanging or placed in the corridor information box. As an Ethernet coaxial terminal product, Ethernet access is performed using a coaxial cable. The EoC terminal device has a built-in Wifi wireless function and includes four 100M Ethernet ports for works with EOC master in Ethernet over coax network.Ability to provide high quality Internet access, voice, IPTV, VoIP and video surveillance.
The optical network terminal product, GPON-1281 Optical modem, constructed as a FTTH network conforms to the ITU-T G.984 standard, WIFI dual- band wireless connection speeds of up to 300 Mbps on 24 GHz .and has dual-band wireless speeds up to 1200 Mbps, supporting 2/3 layer network protocols and high- quality voice transmission. GPON optical network terminals are characterized by reliability, good service quality assurance, manageability scalability, and flexible networking. Can meet data, data + voice, data + voice + WIFI and other access needs.
Simplex indoor optical cable is made by evenly applying strands of aramid yarns as the strength member over tight buffer fibers and then is completed with a flame retardant sheath(CPR-Cca).
The 40G optical module refers to an optical module with a transmission rate of 40 Gbps. CFP and QSFP are the main package types, and the 40G QSFP optical module is one of the most widely used. The 40G QSFP+ optical module is typically used with LC single-mode fiber patch cords for transmission distances up to 10km, and it has four data channels that simultaneously transmit data. It works by the laser driver controlling the wavelength of arrival, and the optical signals are then multiplexed and combined for transmission. When the receiver arrives at the receiving end, the transmitted signals are decomposed into four channels with a transmission rate of 10 Gbps, and then the PIN detector or transimpedance amplifier recovers the data stream and then transmits the optical signal.
BIDI-SFP optical module: BiDi (Bidirectional): single fiber bidirectional. It uses WDM (ie, wavelength division multiplexing) technology to transmit and receive different center wavelengths in two directions, thereby realizing a bidirectional transmission of optical signals in one fiber. A general optical module has two ports, a TX transmitting port and an RX receiving port, and the BIDI optical module has only one port, which is filtered by a filter in the optical module, and simultaneously performs transmission of a 1310 nm optical signal and reception of a 1550 nm optical signal, or in contrast. Therefore, BIDI modules must be used in pairs. It is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking the port with the network. SFPs can be used and interchanged on a wide variety of switches and routers, can be intermixed in combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.
The optical fiber unit, Pre-terminated Drop Cable, is positioned in the center.Two parallel Fiber Reinforced Plastics (FRP) are placed at the two sides.Then,the cable is completed with a black or color LSZH sheath. It is also called leather cable. It is a new type of user access optical cable. According to the application environment and laying conditions, the cable structure and various technical parameters are reasonably designed. The characteristics of indoor soft cable and self-supporting optical cable are collected. Special equipment is used in conjunction with imported precision mold production. It is the best candidate for FTTX network solution, and it is also suitable for users of other fiber-optic FTTO and FTTB networks. Because the cross-section is like a butterfly, it is called a butterfly cable. Both sides are reinforcing members in the leather line and optical fibers in the middle.
The 40G DAC Optical module is usually a cable assembly that is priced at a fixed length with fixed connectors on both ends. The connector used in the high-speed cable end has the same interface as the optical module, but the connector module on the high-speed cable does not have expensive optical lasers and other electronic components compared to the optical module, thereby greatly saving in short-distance applications. Cost and power consumption, a cost-effective, high-speed data communication solution that replaces optical modules, can be widely used in storage area networks, data centers, and high-performance computer connections by connecting switches to routers or servers.